Archive for January, 2012

« Older Entries

San Diego Heating Repair Question: What Causes Cracks in a Heat Exchanger?

Tuesday, January 31st, 2012

Furnaces are designed so that the heat – and the combustion byproduct produced inside – doesn’t interact directly with the outside air. This design is to ensure you have a safer furnace in your San Diego home that won’t inadvertently affect your family’s health.

The metal piece that separates the furnace heat from the outside air stream is called the heat exchanger. The heat exchanger performs a very important function, and if it is broken or cracked, it can’t work properly.

A cracked heat exchanger is very common problem with heating systems, as well as one that should be repaired as soon as possible. But what causes a heat exchanger to crack? Here are some of the most common reasons:

  • A long period of normal use. A furnace heat exchanger naturally expands and contracts with the heat of the furnace, over and over again as the furnace is turned off and on to heat the home. Over several years, this stress can crack the metal.
  • Poor air flow, often caused by dirty or obstructed vents, can result in poor air flow through the furnace. This overworks the furnace, which can crack the heat exchanger prematurely.
  • Poor, incomplete or improper combustion can also cause a heat exchanger to crack. When the combustion process is less efficient – which can also be a result of poor air flow — your furnace’s burners have to run hotter and longer to heat your home, which means extra stress on the heat exchanger.

Essentially, if a furnace is running at less than optimal efficiency for an extended period of time, the heat exchanger is put under additional stress beyond the usual and can crack prematurely. Therefore, the best way to prevent a cracked heat exchanger is proper maintenance, particularly keeping all vents clean and unobstructed and getting an annual maintenance inspection.

If your heat exchanger does crack, do not hesitate to call Cal-West Air Conditioning Inc. and get it repaired. The crack can allow potentially dangerous combustion gases to seep into your San Diego home, which can have a negative impact on your family’s health.

Tags: , , , ,
Posted in Heating | Comments Off

Common Types of Air Cleaning Devices for Fallbrook Homes

Monday, January 30th, 2012

In recent years, you’ve likely heard dozens of warnings in Fallbrook from newscasters, community publications and local contractors about the dangers of indoor pollutants. That’s a good thing – the air in your home, if left untreated, can be a significant health risk to you and your family. But, how do you choose an air cleaner that will get the job done? Let’s take a closer look at the options currently available and what each of them has to offer.

Air Filters

Air filters are the simplest form of air cleaning. They are designed to capture particles that stay airborne long enough to reach the filter. They don’t work well to capture all large particles, however, because they tend to settle before they reach the filter device. Proper air flow is necessary to supplement the process and remove more pollutants.

High efficiency filters with an MERV rating of 14 or higher are recommended, though HEPA filters (which have an MERV of 17-20) are preferred for their ability to capture particles as small as 0.3 microns. In-duct particle removal is a good upgrade as well because it filters moving air and captures more particles.

Gas Phase Filters

These filters are designed to capture gases produced by building materials, household electronics, paint, and your combustion appliances. They are not always effective for long, so filters must be checked and changed frequently. These systems are not frequently used in home systems, but if you have particular pollutants, they may provide a number of clear benefits.

UVGI and PCO Cleaners

These cleaners are designed to kill pollutants like bacteria and mold. They are usually installed in the ductwork or air cleaner and while the effectiveness of either has yet to be properly measured there is a growing trend to include them in systems where homes experience a large number of allergic reactions or asthma symptoms.

Ozone Generators

There are still some systems that produce ozone as they circulate air back and attract it to a filter for removal. The results are mixed and ozone itself can be a significant irritant to the lungs, so it’s unclear whether these actually work very well.

Which Is Best?

It really depends on the pollutants you’re trying to remove. The best course of action is to have your indoor air tested and then discuss with a contractor the best combination of technologies to remove pollutants from your indoor air.

Tags: , ,
Posted in air cleaner, Air Filters, Indoor Air Quality | Comments Off

Clairemont Mesa Heating Maintenance Guide: Downflow Gas Furnaces

Friday, January 27th, 2012

Proper care of your Clairemont Mesa home’s downflow gas furnace starts with proper installation and continues through routine cleaning and maintenance. But before you can even have a downflow gas furnace installed, you need to make sure it’s the right fit for your home.

Downflow gas furnaces are so named because of the direction that air flows through them. The cooler air is taken in at the top and directed downward, heating up as it travels, and then is expelled through the bottom of the furnace into ducts that feed the rest of the house. Because of this configuration, downflow  gas furnaces are typically installed in attics as opposed to basements.

If you have a basement and you’d rather install your furnace there, then an upflow furnace is probably the better choice for you. However, as many newer homes don’t have basements at all, downflow gas furnaces are growing in popularity and usefulness.

As with any other furnace, it’s important to have a downflow gas furnace professionally installed. This will ensure that the venting system is properly in place and that your house will be heated as effectively and efficiently as possible.

Of course, there are some other things you can do to help your furnace heat your home and keep your energy bills down. For instance, make sure you have proper insulation everywhere, particularly in the attic and crawlspaces where much of the normal heat loss in a home occurs.

You can also make your home more airtight in the winter by sealing up any unused windows and doors with plastic and making sure all storm windows are in place. Basically anyplace that a draft could develop, you could be losing heat and that costs you money. So to ensure that all of the money you’re spending to heat your house is actually going to that purpose, check periodically to make sure your home is still sealed up tight.

Also, just like any other type of furnace, a downflow gas furnace will require regular maintenance to make sure it continues to run efficiently and to replace any parts that may have worn out over time. Having a professional Clairemont Mesa technician come out once a year to carry out this type of service will wind up saving you a bunch of money and can help catch problems before they are able to get out of hand.

Tags: , , , , ,
Posted in Heating | Comments Off

Lemon Grove Heat Pump Repair Question: Why Won’t My Heat Pump Start?

Wednesday, January 25th, 2012

If you are having trouble with your Lemon Grove home’s heat pump, you may be surprised to learn that it is probably not the heat pump that is to blame, especially if the trouble is that it simply won’t start up. That seems counterintuitive, but it’s true: the heat pump can be in perfect working order but still not turn on.

The good news, then, is that your heat pump is fine and you won’t have to pay an arm and a leg to fix or replace it. Still though, these types of problems can very frustrating to diagnose and correct. Here are four common culprits when a heat pump won’t start:

  1. No power to the heat pump. Check your breaker box to see if the circuit breaker was tripped. If so, reset it and see if that fixes the problem. Another possibility is that your heat pump is wired to a wall switch, or that there is a switch on the unit itself. Make sure the switch is turned on.
  2. Make sure the thermostat is set to the proper mode, such as “heat” mode if you desire more heat. It seems overly simple, but sometimes the trouble is as simple as that.
  3. A recently replaced thermostat. If you recently upgraded or replaced the thermostat in your home, it’s possible that something went wrong that is preventing your heat pump from starting. It may be the wrong kind of thermostat – heat pumps require a specific type – or it may have been improperly wired.
  4. Finally, the heat pump may have its own circuit breaker on the air handler cabinet. This is often the case with heat pumps that have supplemental electric elements. If that breaker is tripped, that could cause the problems you are experiencing.

If you exhaust these problems and the problem persists or recurs – for example, if the circuit breaker trips again – call a contractor to work on your heat pump. There may be something larger at work that is causing problems in the electrical system that controls your Lemon Grove home’s heat pump, and that requires some expertise to properly address.

Tags: , , , ,
Posted in Heat Pumps | Comments Off

Carmel Valley Furnace Maintenance Guide

Monday, January 23rd, 2012

Depending on its frequency, there are different types of maintenance tasks associated with keeping your automobile in tip top shape. Did you also know there are tasks that can be performed at various intervals to keep your Carmel Valley home’s furnace in peak running condition? Well, there are.

For example, the most frequent maintenance task is checking the filters in your air handling unit. These are often called furnace filters but in reality, they serve the same function to filter air to and from your air conditioner, too. It might be easiest to just call them air filters. The frequency of replacing or cleaning air filters usually depends on the type of indoor environment you live in – like humidity levels, number of household pets or occupants, etc. In general, filter maintenance should occur every one to three months.

A less frequent maintenance task is cleaning the moving parts of the internal mechanism. You may only need to have your furnace cleaned every six months to a year, depending on its use. In some cases you can perform the cleaning yourself or it is included in an annual cleaning as part of a service agreement with a qualified heating and cooling contractor. A furnace can typically run at peak efficiency when it is cleaned on an annual basis.

You can also make it a regular habit of checking the motor bearings and fan belt, too. You can lubricate the bearings and tighten or replace the fan belt on a same schedule as cleaning the moving parts.

Other maintenance tasks related to your furnace, which may require longer interval times include ventilation system cleaning, or more commonly known as duct cleaning. Some homes don’t require this type of maintenance more than every five to ten years – perhaps longer. Unless there are unusually high levels of dust, allergens, or contaminants in the air, most ventilation systems can remain clean for several years.

Of course, you can turn all of your maintenance tasks over to a heating and cooling contractor – and have the most peace of mind.

Tags: , , , , ,
Posted in Heating | Comments Off

Poway Heat Pump Installation Question: What Size Heat Pump Is Right for My Home?

Friday, January 20th, 2012

One of the most important questions to answer when purchasing and installing any new heating or cooling system, no matter what type, is what size is best for your Poway home. You need something that has enough capacity to heat or cool your whole home comfortably; otherwise your house will consistently be at an undesirable temperature.

Some people might think that the quickest solution to this problem is to just buy a system that they are sure has a capacity larger than the size of their home. You may even be tempted to get the biggest model out there, under the logic that the biggest is the best and it will be sure to be able to cover your whole house.

While this line of thinking might make sense to you, it’s actually not a good idea. The problem with this “solution” is that you can wind up with a heat pump that is considerably too large for your needs, which means your home will consistently be either too cool or too hot, and your energy bills will be unnecessarily high.

The best way to choose a new heat pump is to have a Poway professional do a load calculation in your home. This can be a highly technical process, so it is best to leave it to the pros. However, here are some quick tips and other things to consider on the subject:

  • There are a lot of variable to consider in doing a calculation like this. A contractor doing a load calculation will consider the type of construction, what kind of insulation you have installed, what kind of windows you have, whether there is an attic, how many people live there and many more factors.
  • Also, since heat pumps are used for both heating and cooling, different contractors may opt to do the calculation in different ways. Some will estimate capacity based on heating, while others will base it on cooling. Ask to see which is the case for any estimate you receive.
  • If you are getting a new heat pump as a replacement for an existing one, or even a different heating/cooling system, check the capacity of the unit you are replacing. That can be a good place to start. You will at least be in the right ballpark.

All of this means doing some extra leg work up front, but getting the proper sized heat pump is well worth the effort.

Tags: , , , , ,
Posted in Heat Pumps | Comments Off

Clairemont Mesa HVAC Contractor Guide: How to Tell if Your Air Ducts Are Leaking

Wednesday, January 18th, 2012

There are lots of ways for your Clairemont Mesa home to lose energy – through leaky door frames, cracks in window trim, loose or missing insulation, etc. A lot of your indoor heating and cooling winds up outdoors and drives up your utility bills.

One part of your home that is susceptible to leaks and energy loss is your ventilation system, typically metal or flexible ductwork. Older homes generally experience more duct leakage because seals and joints may have loosened over the years or may have not been properly connected when they were installed. There are some ways to check and see – or hear – if the air ducts in your home are leaking.

The most obvious way to check is by listening. Stand, sit, or kneel close to your ductwork. Listen for any hissing noises when the furnace, air conditioner, or blower motor is in operation. A hissing noise is usually an indication of a leak in a seal or joint. Since ductwork comes in a variety of lengths and contains a number of different connectors, there are likely many joints where pieces have been connected. Some joints are sealed with small sheet metal screws while other joints are sealed with duct tape or mastic. Whatever the connection is, the joints may have come loose over time from vibrations, settling of the home’s foundation, previous repairs, or by someone simply bumping into the ductwork.

Another way to check for a leaking air duct is by looking at insulation which may be wrapped around the ductwork. If an air duct is leaking it will leave dark stains on the insulation over time – giving an exact location of the leak.

Leaks in your air ducts can cause areas like your crawlspace, attic, or garage to be abnormally cold or hot. If you are conditioning unused parts of your home inadvertently, it may be because your ductwork is leaking in those areas.

Finally, a not so easy way to check for leaking ducts is to compare utility bills. If there is a big spike in your heating or cooling costs, it may be because of temperature extremes – but it also may be because your ductwork is leaking. You may not be able to see a big difference in your bills unless there are large leaks or breaks in your ductwork, but keep an eye on your energy costs anyway.

Once you have located any leaks, there are some easy fixes. But you also may want to call your local qualified heating and cooling contractor to perform a whole house energy audit, using leak detection instrumentation to check for leaks.

Tags: , , , , , ,
Posted in Indoor Air Quality | Comments Off

Happy Martin Luther King Day from Your San Diego Area Heating and Air Conditioning Contractor!

Monday, January 16th, 2012

Happy Martin Luther King Day! This holiday is not just about celebrating civil rights but also about serving your community. If you have the day off today, why not try spending it helping others? From volunteering at an animal shelter to helping the homeless, there are hundreds of ways you can make your community a better place to live. Have a great holiday!

Tags:
Posted in Holiday | Comments Off

How to Make Your Lakeside Heating System More Effective

Friday, January 13th, 2012

Everyone wants an effective heating system in Lakeside – one that will provide steady, reliable heat without you having to spend hundreds of dollars each month on gas, oil or electricity. And while the best way to improve the efficiency of your heating system in most cases is to upgrade it, there are some simple things you can do around the house to boost its effectiveness. Here are some of the best:

  • Rearrange Furniture – Just having the heat on doesn’t necessarily ensure the heat entering your room is being distributed evenly. Move your furniture in such a way that there is a clear, unimpeded path from the registers and radiators to the rest of the room. Done properly, this will make it much easier to and faster to heat every room of your house.
  • Maximize Air Flow – Air flow can be maximized in a number of ways. Make sure you close any windows near a register or radiator and that you remove any large objects that might block air flow. You should also install things that can help move air like fans and always call someone in for changes to the arrangement of your vents or radiators.
  • Clean Registers or Radiators – The cleaner your radiators or dust registers are, the more efficiently they release their heat. Not only have that, but clean radiators and registers resulted in better indoor air quality. Weekly cleaning of each room’s heating source is highly recommended.
  • Install Ceiling Fans – Ceiling fans switched to blow down are incredibly effective for distributing air throughout the room. This will keep push warm air down and keeps cold air up – in effect, reducing the need for constant running of your furnace.

Effective heating is important to keep your home comfortable, reduce the cost of heating and prolong the lifespan of your furnace. You should also make sure your heating system is properly maintained throughout the year. Skipping maintenance visits (which are highly recommended annually) will put unnecessary stress on your system and shorten its lifespan substantially, not to mention the decrease in efficiency when heating your Lakeside home.

Tags: , , , , , ,
Posted in Heating | Comments Off

El Cajon Furnace Installation Guide: AFUE Ratings

Wednesday, January 11th, 2012

If you’ve been shopping for a furnace in El Cajon, chances are you’ve noticed that each furnace has its own annual fuel utilization efficiency (AFUE) rating. These generally range from 80% to the high 90% s and the higher the number, the more fuel efficient that particular furnace is.

But what does this number really mean and just how much should you care? Well, the AFUE rating should actually have a significant impact on your furnace purchasing decision, but that doesn’t mean that you’ll always choose the furnace with the highest efficiency rating either.

For one thing, you’ll have to recognize that not every type of furnace is capable of running at the highest efficiency levels. Oil furnaces, for instance, can’t compete with the super high efficiency gas furnaces on the market today. That’s not to say that an oil furnace might not be the best choice for you under certain circumstances, but it does mean that you should take a close look at your furnace usage before you make a decision.

If you do choose a gas furnace, you will of course have the option of getting one that can reach up to 97% or so efficiency. However, that may not always be the best choice either. If you live in a place where with very harsh, long winters and you’re going to be using your furnace heavily, then it’s definitely worth investing in a higher AFUE furnace that can save you considerable amounts on your monthly heating bills.

But if you don’t use your furnace too often as your area has more mild winters it’s probably not worth it for you to invest in such a high efficiency product. That’s because the higher the AFUE of the furnace, the more expensive it is to purchase and install. Certainly you’ll save money every month because you’ll be getting more heat out of the fuel you’re paying for. But if you don’t use your furnace all that much, the savings really won’t be that substantial.

Don’t forget that a furnace with an 80% AFUE rating is still quite energy efficient. And once you get up that high, you have to use your furnace a lot for the difference between 80% and 90% to really become apparent. So if you don’t use your furnace heavily during the winter, it will take you many, many years to make up for the higher purchase price of the 90+% AFUE models.

Tags: , , , , , ,
Posted in Heating | Comments Off

« Older Entries