Posts Tagged ‘Carlsbad’

« Older Entries

East San Diego Air Conditioning Tips: Things to Check on Your Broken AC Before Calling a Professional

Wednesday, February 22nd, 2012

A broken air conditioner in East San DIego is a stressful situation, especially since you’re considering whether you need a professional to come out. No one likes spending hundreds of dollars on air conditioning maintenance, so before you call anyone, make sure to check these problems. You may be able to fix the problem on your own without spending a dime.

Thermostat

The thermostat is one of the most common problems you’ll have with an air conditioner.  Make sure the thermostat wasn’t knocked out of position and the sensors near your coils are in the right place. Often times, a bumped sensor or a slightly off thermostat can cause this kind of problem and as a result, you’ll be left without steady cooling.

Check Your Filters

Another common problem that can cause issues with your air conditioner is filter clogging. While the system will continue to run with a clogged filter, there are a few issues that might pop up – it could smell funny or you might notice icing on the outside line (a major problem). If you allow the filter to get so clogged as to block the air flow from your system, you can expect a number of problems to crop up.

Blower Belts

Check the system’s blower belt for damage like cracking, excess slack or general wear. A blower belt that isn’t properly installed or that needs to be replaced will reduce air flow which can result in ice buildup or poor air flow – it will make it harder for your system to maintain a steady temperature.

Check the Outdoor Unit

Check to make sure nothing is blocking the outdoor unit. Clean the condenser coils and remove any debris that might have built up around the outdoor unit. Often, slowed air flow is caused by nothing more than leaves piled in front of your condenser.

If none of these problems is the culprit or if you fix them all and your system continues to struggle, it is time to call Cal-West Air Conditioning.

Tags: , ,
Posted in Air Conditioning, Air Conditioning Repair, Thermostats | Comments Off

Troubleshooting Your Problematic Heat Pump in Carlsbad

Friday, February 10th, 2012

If your heat pump isn’t working properly in Carlsbad, there are a number of things that might be wrong. But, where do you start and how do you solve these problems quickly and inexpensively? Here are some tips for common heat pump problems.

Low Air Flow

Your heat pump is designed to provide steady air flow to the entire house. When it was originally installed, the technician sized it to do so. If it suddenly stops providing enough air flow to your entire house or if the air flow it provides isn’t as comfortable as you’re used to, something is probably wrong.

More specifically, there is likely an issue with the heat pump itself since the device will compensate for most external problems by running longer and harder. Some quick heating maintenance will often rule out serious problems, so you should have someone inspect your device as soon as you notice a problem.

Leaky Duct

If there is an external problem, such as leaky ductwork, it tends not to be as noticeable right away. Often, when ducts are leaking, air flow problems will occur only in certain rooms of your home. Even then, the heat pump might be able to maintain the right temperature in those rooms – you’ll just have a higher energy bill because of the energy loss in the ductwork.

The best way to determine what is happening and how best to tackle the problem is to have someone test your ductwork for leaks, a relatively quick process.

High Energy Bill

If your energy bill suddenly increases dramatically, it is usually due to energy loss somewhere in the transfer between the heat pump and the rooms of your home. Leaky ducts can be the culprit, but so too can the air handler or the heat pump itself. If you notice a sudden increase in your energy bill, look for other symptoms like uneven heating or cooling in certain parts of your home or noises coming from the ductwork or your air handler.

No matter what other symptoms accompany the increase, you probably need repairs. Your home may still be comfortable now, but the heat pump can only make up for the problem for so long and in the interim, it is being put under excessive stress that reduces its lifespan.  If you have any questions about heat pumps please call Cal West Air.

Tags: , ,
Posted in Heat Pumps, Heating, Heating System Maintenance | Comments Off

Poway Heat Pump Installation Question: What Size Heat Pump Is Right for My Home?

Friday, January 20th, 2012

One of the most important questions to answer when purchasing and installing any new heating or cooling system, no matter what type, is what size is best for your Poway home. You need something that has enough capacity to heat or cool your whole home comfortably; otherwise your house will consistently be at an undesirable temperature.

Some people might think that the quickest solution to this problem is to just buy a system that they are sure has a capacity larger than the size of their home. You may even be tempted to get the biggest model out there, under the logic that the biggest is the best and it will be sure to be able to cover your whole house.

While this line of thinking might make sense to you, it’s actually not a good idea. The problem with this “solution” is that you can wind up with a heat pump that is considerably too large for your needs, which means your home will consistently be either too cool or too hot, and your energy bills will be unnecessarily high.

The best way to choose a new heat pump is to have a Poway professional do a load calculation in your home. This can be a highly technical process, so it is best to leave it to the pros. However, here are some quick tips and other things to consider on the subject:

  • There are a lot of variable to consider in doing a calculation like this. A contractor doing a load calculation will consider the type of construction, what kind of insulation you have installed, what kind of windows you have, whether there is an attic, how many people live there and many more factors.
  • Also, since heat pumps are used for both heating and cooling, different contractors may opt to do the calculation in different ways. Some will estimate capacity based on heating, while others will base it on cooling. Ask to see which is the case for any estimate you receive.
  • If you are getting a new heat pump as a replacement for an existing one, or even a different heating/cooling system, check the capacity of the unit you are replacing. That can be a good place to start. You will at least be in the right ballpark.

All of this means doing some extra leg work up front, but getting the proper sized heat pump is well worth the effort.

Tags: , , , , ,
Posted in Heat Pumps | Comments Off

Easy Ways to Lower Your Heat Pump’s Energy Bill: Some Pointers from San Marcos

Wednesday, November 16th, 2011

One of the biggest advantages of a heat pump is that it is highly efficient for both heating and cooling your San Marcos home. However, there is always room for improvement, so here some tips to lower your energy bill even more:

  • Get it checked. It’s been said many times before, but it’s always worth saying again: consistent maintenance is one of the biggest keys to keeping any appliance running efficiently. Get your heat pump inspected by a professional at least once a year. This will keep it in good shape and provide an opportunity to make small repairs, before they have a chance to turn into big problems.
  • Keep it clean. When it comes to HVAC equipment, a clean unit is an efficient unit. Check and replace the filters regularly, according to the manufacturer’s instructions. Keep the coils and fan clean. This will also be part of the annual maintenance, but you can – and should — do touch up cleaning on your own.
  • Install a thermostat. A programmable thermostat is a great energy efficiency tool for any home heating and cooling system, not just a heat pump. A thermostat will keep the temperatures lower during the day or any time no one is home, so that you are not wasting heat.
  • Let it run. It may seem counterintuitive, but turning off a heat pump to save energy may actually do more harm than good. Heat pumps operate most efficiently when they stay running on a regular basis. The components don’t need to take time to spin up, and the refrigerant stays warm so it can keep moving. Your best bet is to have your heat pump connected to a programmable thermostat, program it and then stop thinking about it. You’ll save a bundle over manual operation.
  • Protect the outdoor unit. The outdoor portion of your heat pump has to put up with a lot from the elements. Strong winds can damage them or negatively impact the efficient operation of the pump, so keep the outdoor unit protected from wind.

These simple measures, in combination with a highly efficient heat pump, will help slash your energy bills. In addition, check to see if your heat pump is eligible for a federal tax credit, which can save you even more money.

Tags: , , , , , ,
Posted in Heat Pumps | Comments Off

Why is My Furnace Turning On and Off? A Question from San Diego

Friday, November 4th, 2011

One of the most annoying things your furnace can do in your San Diego home is to constantly keep turning on and off. This on-off cycling keeps your home from heating up properly. This action – called short cycling – also requires more electricity and drives up utility bills.

Short cycling is caused by an overheated furnace, which triggers safety mechanisms and shuts down the furnace. After a brief interval and cooling down, the furnace starts up again the cycle keeps repeating itself. Not only is it an annoyance, it can also signal more serious problems. A leaking heat exchanger can cause a furnace to overheat – and produce deadly carbon monoxide gas.

If a furnace is working too hard and overheating, it is usually because of airflow in and out. Think of the furnace as a human heart. If there is a blockage in the veins and blood flows slowly, a heart has to work harder to pump blood around or through the blockage. Your home’s ventilation system needs to be clear of dirt, dust, and debris. The more blockage in your ductwork and vents, the more friction is created, slowing down airflow and ultimately ending with an overworked furnace that continues to cycle on and off. And a blocked exhaust vent, such as a chimney or dedicated exhaust vent, can also cause a furnace to work harder. Check for things like leaves or bird’s nests.

The blockage may also be coming from a clogged furnace filter. You should clean or replace your furnace filter after a visual inspection reveals any type of build-up of dust or dirt. Do this at least every three-six months.

If you have a two-speed fan on your furnace, it is recommended that you run the fan in low speed during the cold months and high speed in the warm months. The reason? Warm air is lighter and takes less force to move.

There are other measures to take to prevent short cycling but these usually require a professional heating and cooling service technician to correct the problem. If in doubt, call your local qualified heating and cooling contractor and schedule a furnace inspection. Don’t make your furnace work any harder than it was designed for – and keep your home’s occupants comfortable and safe.

Tags: , , , , ,
Posted in Heating | Comments Off

What Happens if You Put Your Air Filter in the Wrong Way? A Question From Carlsbad

Wednesday, October 12th, 2011

Air filters are important pieces in your overall Carlsbad home’s comfort system. They keep unwanted debris and sediment out of your indoor air and they help your system run smoothly for years to come. However, if you’re not careful, an air filter put in backwards can lead to quite a few problems with your heating and cooling system.

The Most Common Problems

The most common problem you will face with a backwards facing filter is simple inefficiency. If your furnace is forced to blow air through the non-porous end of a filter, it will take more energy to do so. The blower will be overworked and you will pay more money for your heating. The same is doubly true for an air conditioner which has multiple filters in place to keep outdoor contaminants out of your indoor air.

Beyond the cost of improper filtering, you will likely suffer from a decrease in indoor air quality. The filter is designed to remove a lot of unwanted debris, but only when installed in a certain direction. If you set your filter up backwards, the normally collective end of the device will not face the air supply. In effect, your filter will help keep debris in the air.

This results in a clogged filter and improperly cleaned air when it reaches your lungs. If you have a home indoor air quality system it will help to supplement this problem for a while, but the clog will eventually become too much for your system.

Avoiding the Problem

There are two ways to avoid improper installation. First, you can have a professional install the system for you. Whenever you need a new filter ask someone to come and take care of it. When they do, though, pay close attention to how they set the filter and any other steps they take. By carefully watching you can ideally learn what it takes to do this step yourself and hopefully keep your system running smoothly for years to come.

Tags: , , , ,
Posted in Indoor Air Quality | Comments Off

When Should You Check Your AC Filters: Some Pointers From Carlsbad

Wednesday, September 28th, 2011

The filters on your air conditioning unit are vital for keeping out the dust and debris that make things like illness, allergies and air quality worse in your Carlsbad home. And it’s important that you take personal responsibility for checking those filters. Sure, you have a professional visit your home once a year to check the air conditioning, but you should also check the system yourself on a semi-regular basis for possible filter degradation.

Monthly Checks

So, how often should you check? Think of it this way. There is no such thing as checking too much, but you can easily not check often enough. So, we recommend checking your filter at least once every 4 weeks. It may not always need to be changed during that four week checkup (sometimes it can last 6 weeks or longer), but it’s good to take a peek.

Why is this so important? Because filters that haven’t been checked and changed as needed have a habit of building up excess sediment and debris. Not a problem when it comes to actually working, but a huge problem when it comes to your energy bill. The harder a system has to work to keep you house cool, the more energy it draws and the more you pay to have cool air in your home. And it will break down much faster as a result of overwork and dirty filters.

Changing an AC Filter

If your filter is ready for a swap, here are some quick tips to get the job done:

  • Find Your Filters – If you don’t know where your filters are, ask your contractor on the next visit or look near the return grills by the thermostat.
  • Remove the Filters – Open the latches and pull the old filter out to check it. You should be able to tell if it looks clean. If this isn’t the case, it’s time for a cleaning/replacement.
  • Clean the Area – Clear the grill and area of any debris and sediment that might make the filter worse after replacement.

Proper filter maintenance only takes five minutes and it will save you money every month you run your AC – not a bad deal for a few minutes’ work.

Tags: , , , ,
Posted in Air Conditioning | Comments Off

How Do I Check for a Dirty Evaporator Coil? A Question From El Cajon

Wednesday, September 21st, 2011

The evaporator coil is an essential piece of your El Cajon home’s air conditioning system. It absorbs heat from air that passes over it, and that air then travels into your home to cool it. So if your coil is dirty or isn’t functioning properly, the cooling power of your air conditioning system is diminished. Fortunately, this problem is fixed easily by cleaning the evaporator coil. You can do this on your own or have a professional come in to take care of it.

Signs of a Dirty Evaporator Coil

The most obvious sign of a dirty evaporator coil is an overall drop in system pressure. As long as you know what constitutes a normal pressure for your system, you should be able to tell if the current pressure is below that level. If it is, a dirty evaporator coil is probably your culprit. You can also check the static pressure in your system to see if that is low, but this requires specialized equipment.

Even if you don’t notice any particular signs that your air conditioning system isn’t working properly, it’s a good idea to clean your evaporator coils once a year or so. This can help prevent any larger problems from developing in the future.

Finding Your Coil

Probably the hardest part of cleaning an evaporator coil is reaching it. Unlike your condenser coil, which is located in your outdoor condenser unit, the evaporator coil is found inside near the air handler or furnace. If you have the owner’s manual, there should be detailed instructions telling you where the coil is and how to safely access it.

Alternately, you can have an HVAC technician show you what to do the next time they come out to work on your system. Whatever you do, though, make sure that power to your AC unit is completely shut off before you start working on it. Once you’ve gained access to the coil, use a brush or vacuum attachment to remove any debris or sediment you find there.

The Importance of Maintenance

Cleaning your evaporator coil is only one part of the regular maintenance required to keep your air conditioning system in good working order for the foreseeable future. There are plenty of things you can do on your own, but it pays to have a professional come out once a year or so to check out the entire system and make any necessary repairs.

Tags: , , , ,
Posted in Air Conditioning | Comments Off

How Often Should I Replace My AC Filter? A Question From Chula Vista

Wednesday, September 14th, 2011

Replacing the filters in your ventilation system regularly is an essential part of Chula Vista home maintenance. It keeps the expensive HVAC machinery running smoothly, saves you money and helps safeguard the health of your loved ones.

How often is often enough to replace your air conditioner filter, though? The short answer is that it depends on your air conditioner, the type of filter and your family’s needs. Below are some guidelines to help you keep it all straight and stay on top of a filter changing schedule.

Rule of Thumb

As a general rule, you should be prepared to change your AC filter every three months when it’s in use. Your filter may require more frequent replacement, which will be discussed in a little more detail below. Although three months is the general rule, you should still inspect your AC filter every month and replace it whenever it’s visibly dirty. That dirt you see not only bogs down the air conditioner, but you may also wind up breathing it in.

More Specifically

There are different kinds of air conditioner filters. Where they vary is in efficiency, which is indicated on a scale called the Minimum Efficiency Reporting Value, or MERV rating. MERV ratings range from 1 to 16, with higher numbers being more efficient at filtering small particles from the air. The standard for homes has been MERV 10 for a while, but that will soon be changing to a more efficient standard.

Essentially, the higher quality air you want in your home, the higher MERV rating you want on your filter. However, a higher MERV rating also means more frequent replacement and higher cost, so choose a rating that is appropriate for your family’s needs. If there is a history of allergies, or you live in an area with poor air quality, you may want a MERV 14 filter. If not, you may be fine with a MERV 11 or 12.

High efficiency filters may need to be changed as often as every month, whereas less efficient ones will be closer to that three month range. No matter what kind of filter you are using, you will have to change it more often if you live in a particularly dusty area, as well as in the summer months when the AC unit is being used more.

Tags: , , , , ,
Posted in Air Conditioning, Indoor Air Quality | Comments Off

Ice in Central Air Conditioning: Why Is This a Problem?

Friday, July 29th, 2011

If your air conditioner does not seem to be working as well as it should, your natural first reaction is to go out and take a look at the compressor to see if there is anything you can do quickly to correct the problem. Of course, you cannot assess the situation unless you know what you are looking for. For instance, if you see ice forming on the condenser coil or anywhere else on the air conditioning system, you will know you found the likely source of the problem.

Ice can form in your air conditioner for a number of reasons. The most common one is that your refrigerant levels are low. Since this refrigerant is contained in a closed system, a deficiency in refrigerant means that there must be a leak somewhere in that system. Only a certified professional can refill your refrigerant and determine where the leaks are in the system to make the necessary repairs.

Another reason that ice can develop in your air conditioner is because the air is not flowing fast enough through the system and across the coils. This can happen because of a problem with the fan or because there is an actual physical impediment to the air flow. Regardless of the reason, the ice will form because without adequate air flow the condenser coils will get too cold.

These coils are typically kept just above freezing by the constant flow of air across them. When the air passes by them at this temperature, the moisture from the air condenses on the surface of the coil. But because the coil is not quite freezing, the water then runs down into a collection pan. When the coil is too cold, however, the moisture from the air will freeze on the coil before it can run off.

This ice actually manages to insulate the coil and keeps it from properly cooling the air or removing any additional moisture. If left unattended, the ice in your central air conditioning system can cause real damage to the unit. Plus, it is not allowing the air conditioner to do its job and cool your house down. So if you notice any amount of ice at all beginning to form on any part of your air conditioner, be sure to call for professional service right away.

Tags: , , ,
Posted in Air Conditioning | Comments Off

« Older Entries