Posts Tagged ‘Heating Repair’

San Diego Heating Repair Question: What Causes Cracks in a Heat Exchanger?

Tuesday, January 31st, 2012

Furnaces are designed so that the heat – and the combustion byproduct produced inside – doesn’t interact directly with the outside air. This design is to ensure you have a safer furnace in your San Diego home that won’t inadvertently affect your family’s health.

The metal piece that separates the furnace heat from the outside air stream is called the heat exchanger. The heat exchanger performs a very important function, and if it is broken or cracked, it can’t work properly.

A cracked heat exchanger is very common problem with heating systems, as well as one that should be repaired as soon as possible. But what causes a heat exchanger to crack? Here are some of the most common reasons:

  • A long period of normal use. A furnace heat exchanger naturally expands and contracts with the heat of the furnace, over and over again as the furnace is turned off and on to heat the home. Over several years, this stress can crack the metal.
  • Poor air flow, often caused by dirty or obstructed vents, can result in poor air flow through the furnace. This overworks the furnace, which can crack the heat exchanger prematurely.
  • Poor, incomplete or improper combustion can also cause a heat exchanger to crack. When the combustion process is less efficient – which can also be a result of poor air flow — your furnace’s burners have to run hotter and longer to heat your home, which means extra stress on the heat exchanger.

Essentially, if a furnace is running at less than optimal efficiency for an extended period of time, the heat exchanger is put under additional stress beyond the usual and can crack prematurely. Therefore, the best way to prevent a cracked heat exchanger is proper maintenance, particularly keeping all vents clean and unobstructed and getting an annual maintenance inspection.

If your heat exchanger does crack, do not hesitate to call Cal-West Air Conditioning Inc. and get it repaired. The crack can allow potentially dangerous combustion gases to seep into your San Diego home, which can have a negative impact on your family’s health.

Tags: , , , ,
Posted in Heating | Comments Off

Carmel Valley Heating Tip: Causes of Delayed Furnace Ignition

Monday, January 9th, 2012

Delayed ignition is usually accompanied by a loud banging or booming sound that resembles a small explosion in your gas appliance. In your Carmel Valley home’s furnace, this can be terrifying and should never be ignored.

What Causes Delayed Ignition

Delayed ignition usually happens when you first turn on your furnace, often after a long delay between use, so usually early in the fall or late in the spring when you don’t necessarily have it on every day of the week.

What happens is moisture builds up over the course of a period of inactivity and begins to corrode the firebox in your furnace. That corrosion builds up to the point that it starts to block the ports that feed gas into the burners. When these ports get blocked, the burners down the line cannot light and when you flip the switch, they won’t light immediately.

Of course, while rust and corrosion are a risk, lint and dust can be equally problematic (and are more common if you don’t have your furnace cleaned properly each fall). Sulfur build up is also a possibility, as it is left behind by burning natural gas. It will appear as a layer of white on the surface of the burners or the pilot light.

When all of this happens and the ports are not cleaned properly, gas will build up in the chamber after it is turned on and, when it finally ignites, create the small boom sound. It doesn’t just sound like an explosion – it is one – and if ignored, it can become incredibly dangerous.

Solving the Problem

Delayed furnace ignition is an easy problem to avoid. All you need to do is have your furnace cleaned properly before turning it on each fall. A Carmel Valley technician will clean the burners and ports and remove any dust, lint, rust or sulfur buildup that might block ignition and cause a delay.

When replacing your furnace, look for a device with corrosion resistant materials. You can learn more about these when it comes time to replace your furnace from a technician. Most importantly, be careful. It may be a small problem now, but if left to build up over time, that small boom can become a much larger one.

Tags: , , , , ,
Posted in Heating | Comments Off

What to Do if Your University City Heating System Breaks

Monday, December 12th, 2011

What if the heart of your University City home’s heating system – the furnace – stops working? The warm air that used to flow from your vents has been replaced by a chilly draft. It isn’t time to panic, but it is time to take action. Before you do anything, determine why the furnace stopped working. It may be something as simple as a tripped circuit breaker in your electrical panel. Check the circuit breakers first.

The pilot light in your furnace may have blown out. It can be re-lit if you follow the directions in your furnace owner’s manual. You can find answers on how to re-light a pilot light on the Internet, too.

If the shutdown has not been caused by an electrical or pilot light failure, there is still no need to panic. But another obvious question is: did you pay your last gas bill? Maybe you had a shutoff notice and either ignored it or forgot about it.

Now that you are convinced that the furnace has pooped out, here are some things you should do. First, find the name of a qualified heating and cooling contractor. If you already use a heating contractor, contact them and schedule a service call.

While you are waiting for help to arrive, ensure that everyone is safe and accounted for. Make sure pets are nearby and protected from the cold, too. What you don’t want to do is use any appliance to keep you warm that is not designed to keep you warm, like a stove. If you have electric space heaters or propane heaters, carefully locate them in a well vented room (windows open a bit or portable fans circulating air). You don’t want any build-up of gases from fossil burning appliances, gases which could contain deadly carbon monoxide.

Huddle up everyone into a room and break out lots of blankets. You may even want to make an “adventure” of this – find a movie to watch and pop up a bunch of popcorn.  If your waiting time is more than 24 hours, you might want to call up a friend or relative and make arrangements to spend the night with them.

The main thing to remember is not to panic. Most qualified heating contractors, knowing the circumstances, will send out a repair person in a matter of minutes or within one or two hours. Just remember to avoid keeping warm by using unvented heating devices.

Tags: , , , , ,
Posted in Heating | Comments Off

Vista Furnace Repair: Another Happy Customer!

Friday, December 9th, 2011

As the weather gets colder, having an HVAC contractor you can rely on is very important. Not only will your heating system need its annual maintenance, but you also need a good person to call for repairs. No one wants to wait for days in a cold house for a technician to arrive; prompt service can make a big difference in an emergency situation.

There are many different problems that occur with your furnace, and some can be quite dangerous. If you suspect a CO leak, call some immediately. Other, less pressing problems are dirty filters, thermostat malfunctions, and ignition problems. All of which Cal West is ready and able to help you with; we are here to make sure your house is comfortable all winter long.

Here is what Mrs. C wrote to use about her furnace repair:

“I was very satisfied by the fast and efficient service I got from Cal-West Air Conditioning. Our furnace completely stopped working on us in the middle of the night. I called Cal-West the next morning and even though they had a full schedule they worked me in. The owner of the company was on my roof that evening well after dark and normal working hours. He found that our 40 year old furnace needed replacement and had it installed the very next morning. Thank you for your prompt service and making sure my family had heat for the Holidays.”

- Mrs. C Vista, CA

So remember to have our number ready for any furnace problems you may encounter. It is always better (and safer!) to address any problems you detect with your furnace sooner rather than later. A quick fix now could save you from a major repair later.

Tags: , , ,
Posted in Heating | Comments Off

Why is My Furnace Turning On and Off? A Question from San Diego

Friday, November 4th, 2011

One of the most annoying things your furnace can do in your San Diego home is to constantly keep turning on and off. This on-off cycling keeps your home from heating up properly. This action – called short cycling – also requires more electricity and drives up utility bills.

Short cycling is caused by an overheated furnace, which triggers safety mechanisms and shuts down the furnace. After a brief interval and cooling down, the furnace starts up again the cycle keeps repeating itself. Not only is it an annoyance, it can also signal more serious problems. A leaking heat exchanger can cause a furnace to overheat – and produce deadly carbon monoxide gas.

If a furnace is working too hard and overheating, it is usually because of airflow in and out. Think of the furnace as a human heart. If there is a blockage in the veins and blood flows slowly, a heart has to work harder to pump blood around or through the blockage. Your home’s ventilation system needs to be clear of dirt, dust, and debris. The more blockage in your ductwork and vents, the more friction is created, slowing down airflow and ultimately ending with an overworked furnace that continues to cycle on and off. And a blocked exhaust vent, such as a chimney or dedicated exhaust vent, can also cause a furnace to work harder. Check for things like leaves or bird’s nests.

The blockage may also be coming from a clogged furnace filter. You should clean or replace your furnace filter after a visual inspection reveals any type of build-up of dust or dirt. Do this at least every three-six months.

If you have a two-speed fan on your furnace, it is recommended that you run the fan in low speed during the cold months and high speed in the warm months. The reason? Warm air is lighter and takes less force to move.

There are other measures to take to prevent short cycling but these usually require a professional heating and cooling service technician to correct the problem. If in doubt, call your local qualified heating and cooling contractor and schedule a furnace inspection. Don’t make your furnace work any harder than it was designed for – and keep your home’s occupants comfortable and safe.

Tags: , , , , ,
Posted in Heating | Comments Off