Posts Tagged ‘Ocean Beach’

East San Diego Air Conditioning Tips: Things to Check on Your Broken AC Before Calling a Professional

Wednesday, February 22nd, 2012

A broken air conditioner in East San DIego is a stressful situation, especially since you’re considering whether you need a professional to come out. No one likes spending hundreds of dollars on air conditioning maintenance, so before you call anyone, make sure to check these problems. You may be able to fix the problem on your own without spending a dime.

Thermostat

The thermostat is one of the most common problems you’ll have with an air conditioner.  Make sure the thermostat wasn’t knocked out of position and the sensors near your coils are in the right place. Often times, a bumped sensor or a slightly off thermostat can cause this kind of problem and as a result, you’ll be left without steady cooling.

Check Your Filters

Another common problem that can cause issues with your air conditioner is filter clogging. While the system will continue to run with a clogged filter, there are a few issues that might pop up – it could smell funny or you might notice icing on the outside line (a major problem). If you allow the filter to get so clogged as to block the air flow from your system, you can expect a number of problems to crop up.

Blower Belts

Check the system’s blower belt for damage like cracking, excess slack or general wear. A blower belt that isn’t properly installed or that needs to be replaced will reduce air flow which can result in ice buildup or poor air flow – it will make it harder for your system to maintain a steady temperature.

Check the Outdoor Unit

Check to make sure nothing is blocking the outdoor unit. Clean the condenser coils and remove any debris that might have built up around the outdoor unit. Often, slowed air flow is caused by nothing more than leaves piled in front of your condenser.

If none of these problems is the culprit or if you fix them all and your system continues to struggle, it is time to call Cal-West Air Conditioning.

Tags: , ,
Posted in Air Conditioning, Air Conditioning Repair, Thermostats | Comments Off

Things to Look for in a New Central Air Conditioning System for Your Mira Mesa Home

Monday, February 13th, 2012

When it comes time to buy a new air conditioner for your Mira Mesa home, there are a lot of factors to consider. Beyond the obvious issues like cost, you need to consider how that system will operate after the air conditioning installation is complete. What factors are most important to you? Control? Comfort? Cost? Here are some things to consider when selecting your new air conditioner.

  • SEER – The Seasonal Energy Efficiency Rating measures the efficiency of your cooling system during a typical hour. To calculate this number, we divide the total BTUs of cooling produced by the watt/hours of electricity consumed during that hour. So, the higher your SEER rating, the less electricity is used to produce the same amount of cooling. Standard SEER ratings are between 11 and 15 these days, but some high end units have SEER ratings of up to 20.
  • Controls – How much control do you want of your system? Many air conditioners these days come with multiple speeds, allowing you to control the air flow as well as the amount of energy consumed by the device in cooling. Do you want it to constantly blow at 100% or would you like it to run at 50% to reduce consumption. Another option available in central air conditioners is zone control, allowing you to determine which rooms receive cooling with separate thermostat settings.
  • Dehumidification – Air conditioners are dehumidifiers by default, but not every system offers the same degree of humidity control. Some simply remove moisture as part of their regular operation. Others have more advanced controls to provide specific humidity control throughout the year.
  • Sound Dampening – Newer models have sound dampening features like insulation and vibration isolation to reduce sound. These are also great for weather protection and help to maintain your system for more years.
  • Refrigerants – Most new air conditioners now use the R410-A refrigerant which will be required in all new units starting in 2020, but there are some lower cost units still using R-22. Check to make sure you have the environmentally friendly coolant offered by newer models.

A good central air conditioner will keep your family cool and comfortable for years to come so make sure to do your research and choose a model that fits your needs in advance. If you’re not sure about any one feature, a professional installer can help you make your decision.

Tags: , ,
Posted in Air Conditioning, AIr Conditioning Installation, Air Filters | Comments Off

San Diego Heating Repair Question: What Causes Cracks in a Heat Exchanger?

Tuesday, January 31st, 2012

Furnaces are designed so that the heat – and the combustion byproduct produced inside – doesn’t interact directly with the outside air. This design is to ensure you have a safer furnace in your San Diego home that won’t inadvertently affect your family’s health.

The metal piece that separates the furnace heat from the outside air stream is called the heat exchanger. The heat exchanger performs a very important function, and if it is broken or cracked, it can’t work properly.

A cracked heat exchanger is very common problem with heating systems, as well as one that should be repaired as soon as possible. But what causes a heat exchanger to crack? Here are some of the most common reasons:

  • A long period of normal use. A furnace heat exchanger naturally expands and contracts with the heat of the furnace, over and over again as the furnace is turned off and on to heat the home. Over several years, this stress can crack the metal.
  • Poor air flow, often caused by dirty or obstructed vents, can result in poor air flow through the furnace. This overworks the furnace, which can crack the heat exchanger prematurely.
  • Poor, incomplete or improper combustion can also cause a heat exchanger to crack. When the combustion process is less efficient – which can also be a result of poor air flow — your furnace’s burners have to run hotter and longer to heat your home, which means extra stress on the heat exchanger.

Essentially, if a furnace is running at less than optimal efficiency for an extended period of time, the heat exchanger is put under additional stress beyond the usual and can crack prematurely. Therefore, the best way to prevent a cracked heat exchanger is proper maintenance, particularly keeping all vents clean and unobstructed and getting an annual maintenance inspection.

If your heat exchanger does crack, do not hesitate to call Cal-West Air Conditioning Inc. and get it repaired. The crack can allow potentially dangerous combustion gases to seep into your San Diego home, which can have a negative impact on your family’s health.

Tags: , , , ,
Posted in Heating | Comments Off

Carmel Valley Heat Pumps and Energy Efficiency

Monday, December 26th, 2011

Heat pumps offer a number of great benefits. For one, they are inclusive heating and cooling solutions, so they can maintain your Carmel Valley home at a comfortable temperature year round without the need for an additional system.

They run on electricity, so you don’t have to worry about the inconvenience of additional bills and keeping a fuel supply around. They are also quiet and relatively easy to maintain—the list goes on and on. The point is, provided you live in a climate where heat pumps can operate properly, they make for great heating and cooling options.

One other huge advantage of heat pumps is that they are very energy efficient, often much more so than other heating and cooling options. For one, the heating efficiency of heat pumps can range from 150-300%, meaning that the amount of heat energy they are able to produce is 1.5 to 3 times greater than the amount of electricity they draw to do it. That is an incredibly efficient exchange.

The United States Environmental Protection Agency awards the EnergyStar to devices and appliances that surpass energy efficiency guidelines. Heat pumps that have earned the EnergyStar are even more efficient than their brethren, sometimes by as much as 9%, according to the EPA. If you have an older heat pump in your home already, a newer EnergyStar rated model may be as much as 20% more efficient.

While these numbers by themselves may not seem Earth shattering, consider two things. First, in an age of constantly escalating energy costs, any savings are welcome. Second, rewarding energy efficient homes has been a focus of the federal government for a few years. To that end, homes with EnergyStar rated heat pumps installed may be eligible for a federal tax credit of up to 30%. So, not only do these devices help you save on your bills, but on your taxes as well.

The benefits of heat pumps are numerous, but perhaps none is a bigger plus than their extremely efficient use of energy. You can save electricity and save money, all while keeping your home comfortable year round.

If you are considering a heat pump for your home, these benefits are important to keep in mind while making your decision.

Tags: , , , , ,
Posted in Heat Pumps | Comments Off

San Marcos HVAC Tip: Where to Place a Thermostat for Accurate Heating

Wednesday, December 21st, 2011

It’s easy to forget that with your furnace in the basement churning away all day to keep your San Marcos home warm, but your thermostat is the single most important device in ensuring your home is heated to the temperature you want. If it stops working or it misreads the temperature inside your home, your furnace won’t know what temperature it actually is and will turn on and off at the wrong time.

Where Not to Place Your Thermostat

To avoid inaccurate readings, avoid placing your thermostat in the following locations:

  • Direct Sunlight – Direct sunlight will almost always increase the perceived temperature of the thermostat. Unless you live in a greenhouse, this will be very uncomfortable for everyone in your home.
  • Windows – Windows can result in direct sunlight and breezes. If the windows are not properly sealed, cold air can blow in and make it seem cooler in your home than it really is. In any of these cases, your thermostat will misread the indoor temperature.
  • Drafts – Drafts from improperly sealed doors, windows, or anything else in your home can negatively impact the thermostat.
  • Heat Vents – Don’t place your thermostat near a radiator or heat vent where it is likely to be warmer than anywhere else in the house.
  • Kitchens – Kitchens tend to be warmer than other rooms in the house, especially when in use. Avoid placing a thermostat here unless you have a zone control system and your kitchen is separate from other rooms.

A properly placed thermostat will ensure your San Marcos home is heated or cooled to the temperature you desire regardless of outdoor conditions. If you’re unsure whether your thermostat is calibrated properly, check the temperature with a separate thermometer in a different location in the same room. If it is significantly warmer or cooler in one place than another, try to determine which is more indicative of the actual comfort level in your home. When properly located, your thermostat should never be an issue again.

Tags: , , , , ,
Posted in Heating | Comments Off

What Size Furnace is Right for My San Marcos Home?

Monday, December 5th, 2011

When it comes to your San Marcos home’s heating equipment, the right size is very important. If your furnace is sized correctly, you will enjoy a high level of indoor comfort, which you should. However, an incorrectly sized furnace may result in many cold spots in your home, an overworked furnace, or higher utility bills.

An undersized furnace will turn off and on frequently, which is called short cycling. Short cycling can lead to moisture in the system, causing less efficiency and damage to equipment from accumulating moisture in the heating system. The constant cycling adds to wear and tear on equipment, too. An oversized furnace may not be able to keep up with the demand for heat during the coldest days. The furnace may be constantly running and unable to keep up – adding to higher utility costs. So size really does matter when it comes to selecting the right heating equipment for your home.

But a big furnace does not mean it is right-sized. Have you ever seen a “five-way” gravity furnace? It was manufactured in the mid-1900’s and took up a lot of room – as much as half of a basement – while being extremely inefficient. The key here is efficiency. A furnace that works right is sized to the space it is heating, which does not include attics, crawlspaces, or uninsulated rooms (porches, mud rooms, etc.).

A furnace must make efficient use of its Btu’s, which is abbreviated for British thermal unit. Btu is used to measure a furnace size. Furnaces are often rated by input Btu, which is the amount of energy consumed when running. The output Btu may be different based on the system. And output Btu is the best way to select a furnace, since this is the actual heating capacity.

When sizing a furnace, the first thing to do is to determine the inside space that will be heated. If you are looking to heat your home, you can measure the square footage of each room (multiply width by length). The rooms should include bathrooms and hallways but exclude attics and crawlspaces. Add up the totals and match up the Btu output to the total square footage. If you aren’t sure of your calculations, call a qualified heating and cooling contractor.

There are many factors that go into heating a home and today’s energy efficient furnaces give homeowners many more choices. Whatever furnace you choose to purchase, make sure you do your homework and hire a qualified professional HVAC contractor to determine the best size furnace for your home.

Tags: , , , ,
Posted in Heating | Comments Off

Green Thinking for Vista’s Green Thinkers

Monday, August 1st, 2011

There are a lot of media stories about exciting new green buildings: LEED-certified buildings, net-zero buildings, buildings made out of recycled shipping containers, homes in New Urbanist communities, even “ultra-small” homes. But a new home can be pricey. Fortunately, though, all these innovative green ideas can be applied where you live right now. In fact, going green in your existing home might even be better for the environment than building a brand-new home in Vista.

If you wish your home could be LEED-accredited, focus on energy conservation and indoor air quality in your existing home. Upgrade to a high-efficiency furnace and air conditioner and consider adding central air filtration to your heating and cooling system. Install Energy Star appliances and WaterSense plumbing fixtures. For remodeling projects, use VOC-free paints and natural materials.

If you wish you had a “net-zero” home, consider geothermal – and insulate. Geothermal systems use 70% renewable energy and protect you against spikes in oil and utility prices. To increase your energy savings still more, tighten the “thermal envelope” of your home by identifying and sealing hidden air leaks and adding insulation.

If you wish you lived in a “recycled” home, get to know your local salvage yard. Many communities have “architectural salvage” shops and recycle/reuse areas in their landfills. When you do your next home improvement project, go shopping at your landfill first. This is not only great for the environment; it’s also great for your budget. Plus, you’ll end up with a creative, unique home. (Of course, make sure that you don’t re-use items containing lead, asbestos, or other contaminants.)

If you wish you lived in a New Urbanist community, start walking and biking in your own community. Experiment with replacing some of your car trips with walking or biking trips. If you find that your community isn’t pedestrian- or bike-friendly, work with local politicians to change this. Learn about your local public transportation options to see if you can fit them into your lifestyle. If you’re in the market for a new home, make location and proximity to work and shops a primary consideration.

If an “ultra-small” home looks like fun but seems impractical as a long-term residence, consider reducing the size of your own living space. If your kids are grown, it may be time to downsize to a smaller home that uses less energy. If you’re building a new home or an addition to your current home, build only what you need. Sometimes the greenest building decision you make can be deciding to build less.

(The “Not So Big House” website (http://www.notsobig.com) is a great resource for those interested in downsizing while maintaining a high quality of life.)

Tags: , , ,
Posted in Energy Savings | Comments Off

How to Use AC Most Efficiently

Monday, June 27th, 2011

Air conditioning is definitely something most of us wouldn’t want to try and get through the summer without. And for a lot of people, because of medical or other conditions, it’s an absolute necessity. But just because you need to run your AC unit all summer doesn’t mean you need to suffer under the weight of astronomical cooling costs.

So if you’re interested in ways to save on cooling without sacrificing comfort, here are a few tips to get you started:

  • Get a Programmable Thermostat – When you come home at the end of a long day, you want your home to be cool and comfortable. But if you only have a basic thermostat, you would have to leave your air conditioning on all day in order to make this possible. Paying to cool an empty house is probably the last thing you want to do. But what is the alternative?

    Programmable thermostats offer the best solution in a case like this. These devices can be easily integrated into just about any home air conditioning system and they allow you to set different temperatures for different times of the day. That means you can have your air conditioning off while you’re not home and set it to come on a half hour or so before you get there. This way, you get the pleasure of walking into a cool, comfortable house without paying extra to keep it that way when you’re not home.

  • Incorporate Passive Cooling – The design of your home and how you use it can also have an effect on how hard your air conditioning system needs to work. Taking steps as simple as closing the blinds to block out the afternoon sun, putting up awnings and making sure that the exterior of your home is painted a lighter color to reflect sunlight rather than a darker one that will absorb it are all excellent ways to reduce the load on your air conditioner.
  • Supplement Your System – You can also take a good chunk out of your cooling bills by using things like ceiling fans in conjunction with your air conditioner. A ceiling fan can effectively lower the indoor temperature several degrees on its own, allowing you to set your thermostat a little higher.

Air conditioning is a major expense that most of us are resigned to paying, but there’s no reason to pay more than necessary with so many strategies available to save money.

Tags: , ,
Posted in Air Conditioning | Comments Off

Tips for Upgrading Your Central Air Conditioner

Wednesday, June 15th, 2011

When the time comes to upgrade your central air conditioner, you will have a lot of things to take into account. If you were generally satisfied with the performance of your old system, it can be very tempting to stick with a similar model. But if you do not examine all of the options out there right now, you may very well be missing out on a great deal.

If you already have a central air conditioner in place, chances are that you also have ductwork throughout your house. In that case, you will probably be better off with a packaged air conditioner as opposed to a split system. If it is a split system you are replacing, however, you should probably keep your search limited to other split systems. Installing a packaged air conditioner when you do not already have ducts in place can dramatically increase the overall cost of the project.

You will also want to make sure that the system you choose is compatible with the heating system and air handler that you already have in place. Most central air conditioning systems can be integrated easily with all types of heating systems, but you should still check to make sure this will not be a problem, particularly if you have an older heating system.

In terms of picking out the right new system for your home, energy efficiency is probably the main factor to consider. While just about every air conditioner on the market right now will be much more efficient than the unit you are replacing, you want to make sure you get a model that will provide you with the optimal savings in the long run.

This does not necessarily mean that you should go out and buy the most energy efficient air conditioner out there. In fact, because the more energy efficient units are also typically more expensive, you may not actually save money by going that route. But you will do well to choose a unit that will save you enough monthly to offset the installation costs and for most people, that means that you will want an air conditioner that is either a SEER 14 or SEER 16.

Of course, the actual amount of money you will save as you move up through the SEER rankings depends on how much you use your air conditioner to begin with. If you live somewhere with very hot weather and you use your unit for a large chunk of the year, it may very well be worth it for you to opt for a very high efficiency model.

Tags: , , , ,
Posted in Air Conditioning | Comments Off